Join Shelby Forums Today

Anyone have a 67 Gt 500 lower pulley?

Discussion in '1965-1970 Shelby Mustang GT350 & GT500' started by carl111sound, Feb 2, 2009.

  1. Feb 2, 2009 #1
    carl111sound

    carl111sound Active Member

    Posts:
    38
    Likes Received:
    0
    Joined:
    Nov 8, 2007
    I recently tried to put my fan on my 67 500 and found that it hits the current pulley I have (just barely) I don't know if I have the wrong pulley or possibly the water pump is pressed together with the shaft too far in possibly?
    The pulley I have is cast and has an "extra" groove as there are 4 total with the assembly complete to the balancer. Is this correct? I was told a while ago that the part number is correct but now I'm not sure. I believe it is CA1N.
    If not does anyone have one for sale?
    Thanks so much everyone.
    Carl
     
    carl111sound, Feb 2, 2009
    carl111sound, Feb 2, 2009
    #1
  2. Feb 2, 2009 #2
    2dragpac500converts

    2dragpac500converts Well-Known Member

    Posts:
    174
    Likes Received:
    1
    Joined:
    Nov 22, 2007
    Location:
    missouri
    Correct balancer is C6AE -A. I am going from memory but I know there is a earlier 427 balancer that is close but doesnt have the correct timing marks and i think the early ones were not machined on front leading edge of the outer part of the blancer. I think it is a C1AE part number. I have seen some balancers that were restamped from C1AE to C6AE from the factory though. The correct pulley is 2 groove and looks very similar to a cj lower pulley when assembled. I think its parts number is C1AE.
    The correct balancer is expensive.
     
    2dragpac500converts, Feb 2, 2009
    2dragpac500converts, Feb 2, 2009
    #2
  3. Feb 2, 2009 #3
    carl111sound

    carl111sound Active Member

    Posts:
    38
    Likes Received:
    0
    Joined:
    Nov 8, 2007
    Thanks Dragpac,
    Actually I'm asking about the pulley not the balancer, any thoughts?
    Thanks,
    Carl
     
    carl111sound, Feb 2, 2009
    carl111sound, Feb 2, 2009
    #3
  4. Feb 2, 2009 #4
    TLEA

    TLEA Well-Known Member

    Age:
    67
    Posts:
    887
    Likes Received:
    11
    Joined:
    Oct 17, 2005
    Location:
    Warwick, Rhode Island
    Correct pulley is C1AE A casting#

    [​IMG]
     
    TLEA, Feb 2, 2009
    TLEA, Feb 2, 2009
    #4
  5. Feb 2, 2009 #5
    2dragpac500converts

    2dragpac500converts Well-Known Member

    Posts:
    174
    Likes Received:
    1
    Joined:
    Nov 22, 2007
    Location:
    missouri
    Correct pulley is C1AE-A Its a 2 groove pulley the inner most pulley is the same size as the one made on the balancer and the outer is smaller. Looks alot like a 428 cj lower pulley when together.
     
    2dragpac500converts, Feb 2, 2009
    2dragpac500converts, Feb 2, 2009
    #5
  6. Jan 14, 2012 #6
    67GT500 427 SO

    67GT500 427 SO Member

    Posts:
    8
    Likes Received:
    0
    Joined:
    Jan 14, 2012
    I have a spare pulley if needed. Feel free to drop me a mesage if you're still in need.

    -Dan
     
    67GT500 427 SO, Jan 14, 2012
    67GT500 427 SO, Jan 14, 2012
    #6
  7. Jan 14, 2012 #7
    Bob Gaines

    Bob Gaines Well-Known Member

    Posts:
    1,146
    Likes Received:
    37
    Joined:
    Jan 7, 2006
    Dan, it was nice of you to offer to help however in case you are not aware the post you are responding to was in 2009 . The date is in the blue ribbon at the top of the post. Bob
     
    Bob Gaines, Jan 14, 2012
    Bob Gaines, Jan 14, 2012
    #7
  8. Jan 15, 2012 #8
    carl111sound

    carl111sound Active Member

    Posts:
    38
    Likes Received:
    0
    Joined:
    Nov 8, 2007
    Yes thanks a bunch but I eventually found one at a Cougar place in Cali.
    Thanks,
    Carl
     
    carl111sound, Jan 15, 2012
    carl111sound, Jan 15, 2012
    #8

Share This Page